Order from us for quality, customized work in due time of your choice.
Case Study: Supply Chain Design
The Darby Company manufactures and distributes m
Case Study: Supply Chain Design
The Darby Company manufactures and distributes meters used to measure electric power consumption. The company started with a small production plant in El Paso and gradually built a customer base throughout Texas. A distribution center was established in Fort Worth, Texas, and later, as business expanded, a second distribution center was established in Santa Fe, New Mexico.
The El Paso plant was expanded when the company began marketing its meters in Arizona, California, Nevada, and Utah. With the growth of the West Coast business, the Darby Company opened a third distribution center in Las Vegas and just two years ago opened a second production plant in San Bernardino, California.
Manufacturing costs differ between the company’s production plants. The cost of each meter produced at the El Paso plant is $10.50. The San Bernardino plant utilizes newer and more efficient equipment; as a result, manufacturing cost is $0.50 per meter less than at the El Paso plant.
Due to the company’s rapid growth, not much attention had been paid to the efficiency of its supply chain, but Darby’s management decided that it is time to address this issue. The cost of shipping a meter from each of the two plants to each of the three distribution centers is shown in Table 6.10.
Table 6.10
Shipping Cost Per Unit from Production Plants to Distribution Centers ($)
Distribution Center
Plant
Fort Worth
Santa Fe
Las Vegas
El Paso
3.20
2.20
4.20
San Bernardino
—
3.90
1.20
The quarterly production capacity is 30,000 meters at the older El Paso plant and 20,000 meters at the San Bernardino plant. Note that no shipments are allowed from the San Bernardino plant to the Fort Worth distribution center.
The company serves nine customer zones from the three distribution centers. The forecast of the number of meters needed in each customer zone for the next quarter is shown in Table 6.11.
Table 6.11
Quarterly Demand Forecast
Customer Zone
Demand (meters)
Dallas
6300
San Antonio
4880
Wichita
2130
Kansas City
1210
Denver
6120
Salt Lake City
4830
Phoenix
2750
Los Angeles
8580
San Diego
4460
The cost per unit of shipping from each distribution center to each customer zone is given in Table 6.12; note that some distribution centers cannot serve certain customer zones. These are indicated by a dash, “—”.
Table 6.12
Shipping Cost from the Distribution Centers to the Customer Zones ($)
Customer Zone
Distribution Center
Dallas
San Antonio
Wichita
Kansas City
Denver
Salt Lake City
Phoenix
Los Angeles
San Diego
Fort Worth
0.30
2.10
3.10
4.40
6.00
—
—
—
—
Santa Fe
5.20
5.40
4.50
6.00
2.70
4.70
3.40
3.30
2.70
Las Vegas
—
—
—
—
5.40
3.30
2.40
2.10
2.50
In its current supply chain, demand at the Dallas, San Antonio, Wichita, and Kansas City customer zones is satisfied by shipments from the Fort Worth distribution center. In a similar manner, the Denver, Salt Lake City, and Phoenix customer zones are served by the Santa Fe distribution center, and the Los Angeles and San Diego customer zones are served by the Las Vegas distribution center. To determine how many units to ship from each plant, the quarterly customer demand forecasts are aggregated at the distribution centers, and a transportation model is used to minimize the cost of shipping from the production plants to the distribution centers. LO 3
Managerial Report
You are asked to make recommendations for improving Darby Company’s supply chain. Your report should address, but not be limited to, the following issues:
If the company does not change its current supply chain, what will its distribution costs be for the following quarter?
Suppose that the company is willing to consider dropping the distribution center limitations; that is, customers could be served by any of the distribution centers for which costs are available. Can costs be reduced? If so, by how much?
The company wants to explore the possibility of satisfying some of the customer demand directly from the production plants. In particular, the shipping cost is $0.30 per unit from San Bernardino to Los Angeles and $0.70 from San Bernardino to San Diego. The cost for direct shipments from El Paso to San Antonio is $3.50 per unit. Can distribution costs be further reduced by considering these direct plant-to-customer shipments?
Over the next five years, Darby is anticipating moderate growth (5000 meters) to the north and west. Would you recommend that Darby consider plant expansion at this time?
Paper Outline
1. Cover page
2. Introduction
3. Draw a network diagram
4. Write the linear program
ex. Min
s.t
5. Run the linear program through LINGO and get the result
6. Answer the questions in the Managerial report section
Order from us for quality, customized work in due time of your choice.